EiffelVision Pick and Drop

Pick-and-Drop is a unique user-interface action that permits a user to request an action be performed on a specified object. It is a more-ergonomic alternative to the typical drag-and-drop or "select-and-click" user operations found in most modern graphical user interfaces. Users of EiffelStudio have come to value Pick-and-Drop as both intuitive, and easier on the wrist and fingers with long-term use.

Pick-and-Drop uses the metaphor of pebbles and holes. The typical method of doing a pick-and-drop is that the end user selects the object to receive an action with a single right-click of the mouse. At that point, the mouse arrow turns into a "pebble" connected to the "point of picking" via a visible "band". This "pebble" is often a symbol representing the type of object that was "picked". In the case of the screen-shot below, it is a blue ellipse: the "pebble" symbol for a class.

EiffelStudio During Class Pick-and-Drop

The "pebble" may then be dropped into any compatible "hole" (drop target—a widget configured to accept "pebbles" of this type). Such "receiving" widgets are often tool-bar buttons or editing areas (or in the case of the screen-shot above, the editor "tab" bar), but can be any widget that inherits from EV_PICK_AND_DROPABLE and is properly configured. The user then can either "drop the pebble into the hole" with a second right-click (on the receiving object), or may cancel the operation by single-clicking the left mouse button.

EiffelStudio After Class Pick-and-Drop

Note: See Retargeting Through Pick-and-Drop to see how EiffelStudio uses the Pick-and-Drop user interface.

Because the Pick-and-Drop operation has been so popular, classes have been added to the EiffelVision 2 library to make implementing this user interface very easy.

From a technical viewpoint, Pick-and-Drop is a mechanism which allows data to be transported from a source object to a target. Any EiffelVision 2 object inheriting from EV_PICK_AND_DROPABLE can be used to transport or receive data.

A Simple Pick-and-Drop Example

The two necessary components for a Pick-and-Drop operation are a source and a target, both of which must conform to EV_PICK_AND_DROPABLE. The data that is to be transported is known as a pebble.

The following steps need to be undertaken to set up a simple pick and drop:

• Set the source by calling set_pebble.
• Set one or more targets by adding an agent to their drop_actions list. To make the target accept that type of pebble, the arguments of the agent must match the type of the pebble to be transported for the source. Otherwise the transport will not be permitted.

A simple example of this is demonstrated here: button1.set_pebble ("A PND transport has occured%N") button2.drop_actions.extend (agent print (?))

Because print takes an argument of type STRING_8, button2 becomes a valid drop-target for the pebble contained by button1. Right clicking the mouse pointer over the source will start the transport, and right clicking with the mouse pointer over a valid target will complete the transport. The transport can be canceled anytime with a simple left click, just as you would do in EiffelStudio.

Note: Any type of object can be used as the pebble. When a transport completes, the pebble that was transported is passed as an argument to all agents in the target's drop_actions list to which the pebble conforms.

Three Different Modes of Transport

There are three different modes of transport available for pick and drop. They are listed below with details of their use:

• Pick and Drop Mode.
  
• Drag and Drop Mode
  
• Target Menu Mode
  

This is the default mode for pick and drop, but can be set by calling set_pick_and_drop_mode on the source object. Right clicking on a source starts the transport and right clicking on a valid target completes the transport. During execution, a band is drawn from the screen position where the pick started to the current mouse position. Pressing the left mouse button or the escape key during execution will end the transport. This mode can be set by calling set_drag_and_drop_mode on the source object. Left clicking on a source starts the transport and releasing the left mouse button over a valid target completes the transport. During execution, a band is drawn from the screen position where the pick started to the current mouse position. Releasing the left mouse button or pressing the escape key during execution will end the transport. This mode can be set by calling set_target_menu_mode on the source object. Right clicking on a source brings up a menu of all the valid drop targets in the system. Selecting one of these targets completes the transport.

Accept and Deny Cursors

When mode_is_pick_and_drop or mode_is_drag_and_drop then the shape of the mouse cursor changes to reflect whether the current GUI component below the mouse accepts the pebble or not. Calling set_accept_cursor or set_deny_cursor on the source object allows you to customize the Accept- and Deny-Cursor respectively—used to represent a valid or invalid target respectively while the mouse pointer (pebble) is being moved around. The default Accept-Cursor is the standard mouse pointer. The default Deny-Cursor is a red circle with a diagonal line across it: the universal "not permitted" symbol.

Example:

add_some_widgets -- Add some widgets with a Pick-and-Drop example into `main_window'. local my_hbox: EV_HORIZONTAL_BOX my_button1: EV_BUTTON my_button2: EV_BUTTON bullseye_pix_buffer: EV_PIXEL_BUFFER bullseye_ptr_style: EV_POINTER_STYLE do create my_hbox create my_button1.make_with_text ("Button1") create my_button2.make_with_text ("Button2") my_hbox.extend (my_button1) my_hbox.extend (my_button2) my_hbox.extend (create {EV_BUTTON}.make_with_text ("Button3")) main_window.extend (my_hbox) my_button2.set_pebble ("A Pick-and-Drop has occurred.") my_button1.drop_actions.extend (agent my_button1.set_text (?)) my_button1.drop_actions.extend (agent io.put_string (?)) create bullseye_pix_buffer.make_with_size (32, 32) bullseye_pix_buffer.set_with_named_file ("BULLSEYE.png") create bullseye_ptr_style.make_with_pixel_buffer (bullseye_pix_buffer, 32, 32) my_button2.set_accept_cursor (bullseye_ptr_style) end